Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
accessory:add-on_boards:xu4_cloudshell2:cs2_assembling2 [2017/08/04 13:40] john1117 [Package include] |
accessory:add-on_boards:xu4_cloudshell2:cs2_assembling2 [2017/09/07 10:18] (current) john1117 [Assembly guide] |
||
|---|---|---|---|
| Line 10: | Line 10: | ||
| D. Front piece\\ | D. Front piece\\ | ||
| E. Rear piece\\ | E. Rear piece\\ | ||
| - | F. Top_2 piece\\ | + | F. Fan_holder piece\\ |
| - | G. Top_3 piece\\ | + | G. Top_holder piece\\ |
| H. Locker piece\\ | H. Locker piece\\ | ||
| </color> | </color> | ||
| Line 27: | Line 27: | ||
| Q. 4x 8mm female hex XU4 spacer\\ | Q. 4x 8mm female hex XU4 spacer\\ | ||
| R. 8x 5mm Round Head\\ | R. 8x 5mm Round Head\\ | ||
| - | S. 12x 10mm Round Head | + | S. 12x 10mm Round Head\\ |
| </color> | </color> | ||
| + | |||
| ====== Assembly guide ====== | ====== Assembly guide ====== | ||
| - | ^ 1. ^^ 2. ^^ | + | ^ 1. |^ 2. || |
| - | |{{:en:acc:cs2:asm0.jpg?200 |}}|Screw the left and right pieces\\ to the hard disks. (A + B + P)|{{:en:acc:cs2:asm1.jpg?200 |}}|Attach the Cloudshell-2 board\\ to the hard disks.(K)| | + | | {{:accessory:add-on_boards:xu4_Cloudshell2:asm_1.jpg?200 }} | Screw the left and right pieces\\ to the hard disks. (<color #ff0000>A</color> + <color #ff0000>B</color> + <color #0000ff>S</color>) | {{:accessory:add-on_boards:xu4_cloudshell2:asm_2.jpg?200 }} | Attach the Cloudshell-2 board\\ to the hard disks.(<color #22b14c>N</color>) | |
| - | ^ 3. ^^ 4. ^^ | + | ^ 3. |^ 4. || |
| - | |{{:en:acc:cs2:asm2.jpg?200 |}}|Screw [[accessory:add-on_boards:xu4_cloudshell2:cloudshell]]-2 board\\ to left/right pieces. (O)|{{:en:acc:cs2:asm3.jpg?200 |}}|Assemble the FAN and back piece and\\ place the FAN at the back side.\\ Use only 3 screws in this step. (E + G + N)| | + | | {{:accessory:add-on_boards:xu4_cloudshell2:asm_3.jpg?200 }} | Screw the Cloudshell-2 board\\ to left/right pieces. (<color #0000ff>O</color>) | {{:accessory:add-on_boards:xu4_cloudshell2:asm_4_1.jpg?200 }} | Assemble the FAN and back piece and\\ place the FAN at the back side.\\ Use only 3 screws in this step. (<color #ff0000>E</color> + <color #22b14c>I</color> + <color #0000ff>P</color>) | |
| - | ^ 5. ^^ 6. ^^ | + | ^ 5. |^ 6. || |
| - | |{{:en:acc:cs2:asm4.jpg?200 |}}|Insert the FAN cable\\ to the [[accessory:add-on_boards:xu4_cloudshell2:cloudshell]]-2 board.|{{:en:acc:cs2:fan_quiet.png?200|}}|__**If you want to use quiet fan mode,\\ connect the current limit PCB between \\ the FAN cable connector and \\ the Cloudshell-2 board.**__| | + | | {{:accessory:add-on_boards:xu4_cloudshell2:asm_5.jpg?200 }} | Insert the FAN cable\\ to the Cloudshell-2 board. | {{:accessory:add-on_boards:xu4_cloudshell2:asm_6.jpg?200 }} | __**If you want to use quiet fan mode,\\ connect the current limit PCB between \\ the FAN cable connector and \\ the Cloudshell-2 board.**__ | |
| - | ^ 7. ^^ 8. ^^ | + | ^ 7. |^ 8. || |
| - | |{{:en:acc:cs2:asm5.jpg?200 |}}|Assemble the ODROID-XU4 and\\ XU4 holder pieces. (J + M + Q + R)|{{:en:acc:cs2:asm6.jpg?200 |}}|Connect micro B side of USB 3.0 cable\\ to the Cloudshell-2 board. (H + K)| | + | | {{:accessory:add-on_boards:xu4_cloudshell2:asm_7_1.jpg?200 }} | Assemble the ODROID-XU4 and\\ XU4 holder pieces. (<color #ff0000>C</color> + <color #0000ff>Q</color> + <color #0000ff>R</color>) | {{:accessory:add-on_boards:xu4_cloudshell2:asm_8.jpg?200 }} | Connect micro B side of USB 3.0 cable\\ to the Cloudshell-2 board. (<color #22b14c>K</color> + <color #22b14c>N</color>) | |
| - | ^ 9. ^^ 10. ^^ | + | ^ 9. |^ 10. || |
| - | |{{:en:acc:cs2:asm7.jpg?200 |}}|Connect GPIO ribbon cable \\ between ODROID-XU4 and\\ [[accessory:add-on_boards:xu4_cloudshell2:cloudshell]]-2 board. (F + K)|{{:en:acc:cs2:asm8.jpg?200 |}}|Connect type A side of USB 3.0 cable\\ to ODROID-XU4.| | + | | {{:accessory:add-on_boards:xu4_cloudshell2:asm_9.jpg?200 }} | Connect GPIO ribbon cable \\ between ODROID-XU4 and\\ Cloudshell-2 board. (<color #22b14c>M</color> + <color #22b14c>N</color>) | {{:accessory:add-on_boards:xu4_cloudshell2:asm_10.jpg?200 }} | Connect type A side of USB 3.0 cable\\ to ODROID-XU4. | |
| - | ^ 11. ^^ 12. ^^ | + | ^ 11. |^ 12. || |
| - | |{{:en:acc:cs2:asm9.jpg?200 |}}|Place the front piece\\ at the front side. (C)|{{:en:acc:cs2:asm10.jpg?200 |}}|Cover the top piece on the top. (D)| | + | | {{:accessory:add-on_boards:xu4_cloudshell2:asm_11.jpg?200 }} | Place the front piece\\ at the front side. (<color #ff0000>D</color>) | {{:accessory:add-on_boards:xu4_cloudshell2:asm_12.jpg?200 }} | Cover the top piece and insert the top_holder on the top . (<color #ff0000>C</color> + <color #ff0000>G</color>) | |
| - | ^ 13. ^^ | + | ^ 13. |^ 14. || |
| - | |{{:en:acc:cs2:asm11.jpg?200 |}}|Put the locker piece and screw it. (I + N)| | + | | {{:accessory:add-on_boards:xu4_cloudshell2:asm_13.jpg?200 }} | Keep the line on the side to insert the fan_holder. | {{:accessory:add-on_boards:xu4_cloudshell2:asm_13_1.jpg?200 }} | Slide fan_holder piece to fix the top_holder piece on the Fan. (<color #ff0000>F</color>) | |
| + | ^ 15. || | | | ||
| + | | {{:accessory:add-on_boards:xu4_cloudshell2:asm_14.jpg?200 }} | Put the locker piece and screw it. (<color #ff0000>H</color> + <color #0000ff>P</color>) | | | | ||
