Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision
Previous revision
odroid-h2:application_note:external_power_switch [2018/11/19 16:50]
luke.go created
odroid-h2:application_note:external_power_switch [2020/06/11 18:18]
neal [Install a Power Switch]
Line 12: Line 12:
 Red wire: LED positive (Anode) : pin-4 or pin-7 or pin-14 on 20 pin header of ODROID-H2\\ Red wire: LED positive (Anode) : pin-4 or pin-7 or pin-14 on 20 pin header of ODROID-H2\\
 Black wire: LED negative (Cathode) : GND(pin-1) on 20 pin header of ODROID-H2\\ Black wire: LED negative (Cathode) : GND(pin-1) on 20 pin header of ODROID-H2\\
-Blue wire : Switch-A : #​PWR_BTN(pin-17) in 20 pin header of ODROID-H2\\ +Green wire : Switch-A : #​PWR_BTN(pin-17) in 20 pin header of ODROID-H2\\ 
-Green wire : Switch-B: GND(pin-19) on 20 pin header of ODROID-H2\\+Blue wire : Switch-B: GND(pin-19) on 20 pin header of ODROID-H2\\
  
 This blue illuminated power button has a built-in LED which turns on when the system power is on.\\ This blue illuminated power button has a built-in LED which turns on when the system power is on.\\
Line 19: Line 19:
 If you need to use "​+3.3V"​ for another device, you also can use UART_RTS# alternatively.\\ If you need to use "​+3.3V"​ for another device, you also can use UART_RTS# alternatively.\\
  
-{{:internal:odroid-h2:​hardware:​ledpower.png|}}+{{odroid-h2:​hardware:​ledpower.png|}}
 ==== Install a Power Switch ==== ==== Install a Power Switch ====
-=== When connect to +3.3V === +Download fritzing \\ 
-{{:internal:odroid-h2:hardware:pwr_btn_3v3.jpg?600| +3.3V}}+- Illuminated_powerbtn part ☞ {{ :​odroid-h2:​application_note:​illuminated_powerbtn.fzpz |}} \\ 
 +- ODROID-H2 part ☞ {{ :odroid-h2:​application_note:odroid-h2.fzpz |}} \\ 
 +- ODROID-H2+ part ☞ {{ :odroid-h2:application_note:​odroid-h2plus.fzpz |}}\\ 
 +- fritzing parts(H2) ☞ {{ :​odroid-h2:​application_note:​illuminated_powerbtn.fzz |}} \\ 
 +- fritzing parts(H2+) ☞ {{ :​odroid-h2:​application_note:​h2plus_illuminated_powerbtn.fzz |}} \\
  
-=== When connect to UART_RTS1# === +<tabbox H2+> 
-{{:internal:odroid-h2:hardware:pwr_btn_rts1.jpg?​600| ​UART_RTS1#}}+{{:​odroid-h2:​application_note:h2plus_illuminated_powerbtn.jpg?600|}}\\
  
-=== When connect to UART_RTS2# ​=== +<fs x-large>​**When connect to +3.3V**</​fs>​\\ 
-{{:internal:​odroid-h2:​hardware:​pwr_btn_rts2.jpg?​600| UART_RTS2#​}}+{{:​odroid-h2:​application_note:​h2plus_btn_3v3.jpg?​600| +3.3V}} 
 + 
 +<fs x-large>​**When connect to UART_RTS1#​**</​fs>​\\ 
 +{{:​odroid-h2:​application_note:​h2plus_btn_uart1_rts.jpg?​600| UART_RTS1#​}} 
 + 
 +<fs x-large>​**When connect to UART_RTS2#**</​fs>​\\ 
 +{{:odroid-h2:​application_note:​h2plus_btn_uart2_rts.jpg?​600| UART_RTS2#​}} 
 +<tabbox H2> 
 +{{:odroid-h2:​application_note:​ex_power_sw.png?​600|}}\\ 
 + 
 +<fs x-large>​**When connect to +3.3V**</​fs>​\\ 
 +{{odroid-h2:​hardware:​pwr_btn_3v3.jpg?​600| +3.3V}} 
 + 
 +<fs x-large>​**When connect to UART_RTS1#​**</​fs>​\\ 
 +{{odroid-h2:​hardware:​pwr_btn_rts1.jpg?​600| UART_RTS1#​}} 
 + 
 +<fs x-large>​**When connect to UART_RTS2#​**</​fs>​\\ 
 +{{odroid-h2:​hardware:​pwr_btn_rts2.jpg?​600| UART_RTS2#​}} 
 +</​tabbox>​