Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Last revision Both sides next revision
odroid-h2:application_note:external_power_switch [2018/11/20 10:34]
luke.go ↷ Page moved from internal:odroid-h2:application_note:external_power_switch to odroid-h2:application_note:external_power_switch
odroid-h2:application_note:external_power_switch [2020/06/11 17:20]
neal [Install a Power Switch]
Line 12: Line 12:
 Red wire: LED positive (Anode) : pin-4 or pin-7 or pin-14 on 20 pin header of ODROID-H2\\ Red wire: LED positive (Anode) : pin-4 or pin-7 or pin-14 on 20 pin header of ODROID-H2\\
 Black wire: LED negative (Cathode) : GND(pin-1) on 20 pin header of ODROID-H2\\ Black wire: LED negative (Cathode) : GND(pin-1) on 20 pin header of ODROID-H2\\
-Blue wire : Switch-A : #​PWR_BTN(pin-17) in 20 pin header of ODROID-H2\\ +Green wire : Switch-A : #​PWR_BTN(pin-17) in 20 pin header of ODROID-H2\\ 
-Green wire : Switch-B: GND(pin-19) on 20 pin header of ODROID-H2\\+Blue wire : Switch-B: GND(pin-19) on 20 pin header of ODROID-H2\\
  
 This blue illuminated power button has a built-in LED which turns on when the system power is on.\\ This blue illuminated power button has a built-in LED which turns on when the system power is on.\\
Line 19: Line 19:
 If you need to use "​+3.3V"​ for another device, you also can use UART_RTS# alternatively.\\ If you need to use "​+3.3V"​ for another device, you also can use UART_RTS# alternatively.\\
  
-{{:internal:odroid-h2:​hardware:​ledpower.png|}}+{{odroid-h2:​hardware:​ledpower.png|}}
 ==== Install a Power Switch ==== ==== Install a Power Switch ====
-=== When connect to +3.3V === +Download fritzing \\ 
-{{:internal:odroid-h2:hardware:pwr_btn_3v3.jpg?600| +3.3V}}+- Illuminated_powerbtn part ☞ {{ :​odroid-h2:​application_note:​illuminated_powerbtn.fzpz |}} \\ 
 +- ODROID-H2 part ☞ {{ :odroid-h2:​application_note:odroid-h2.fzpz |}} \\ 
 +- ODROID-H2+ part ☞ {{ :odroid-h2:application_note:​odroid-h2plus.fzpz |}}\\ 
 +- fritzing parts(H2) ☞ {{ :​odroid-h2:​application_note:​illuminated_powerbtn.fzz |}} \\ 
 +- fritzing parts(H2+) ☞ {{ :​odroid-h2:​application_note:​h2plus_illuminated_powerbtn.fzz |}} \\
  
-=== When connect to UART_RTS1# === +<tabbox H2+> 
-{{:internal:odroid-h2:hardware:pwr_btn_rts1.jpg?​600| ​UART_RTS1#}}+{{:​odroid-h2:​application_note:h2plus_illuminated_powerbtn.jpg?600|}}\\
  
-=== When connect to UART_RTS2# ​=== +<fs x-large>​**When connect to +3.3V**</​fs>​\\ 
-{{:internal:​odroid-h2:​hardware:​pwr_btn_rts2.jpg?​600| UART_RTS2#​}}+{{odroid-h2:​hardware:​pwr_btn_3v3.jpg?​600| +3.3V}} 
 + 
 +<fs x-large>​**When connect to UART_RTS1#​**</​fs>​\\ 
 +{{odroid-h2:​hardware:​pwr_btn_rts1.jpg?​600| UART_RTS1#​}} 
 + 
 +<fs x-large>​**When connect to UART_RTS2#**</​fs>​\\ 
 +{{odroid-h2:hardware:​pwr_btn_rts2.jpg?​600| UART_RTS2#​}} 
 +<tabbox H2> 
 +{{:odroid-h2:​application_note:​ex_power_sw.png?​600|}}\\ 
 + 
 +<fs x-large>​**When connect to +3.3V**</​fs>​\\ 
 +{{odroid-h2:​hardware:​pwr_btn_3v3.jpg?​600| +3.3V}} 
 + 
 +<fs x-large>​**When connect to UART_RTS1#​**</​fs>​\\ 
 +{{odroid-h2:​hardware:​pwr_btn_rts1.jpg?​600| UART_RTS1#​}} 
 + 
 +<fs x-large>​**When connect to UART_RTS2#​**</​fs>​\\ 
 +{{odroid-h2:​hardware:​pwr_btn_rts2.jpg?​600| UART_RTS2#​}} 
 +</​tabbox>​