ODROID-XU4
XU4 PCB revision history
| LOT-ID | PCB Revision | Description |
| EL-1507 | rev0.1 20150527 | The first production version |
| EL-1510 | rev0.1 20150825 | Add a R99 of Pull-Down resistor on the PMIC PSHOLD signal. Add a C289 of dummy capacitor for physical balancing the heatsink on the PCB |
| EL-1511 | rev0.1 20150825 | |
| EL-1601 | rev0.1 20150825 | |
| EL-1603 | rev0.1 20151201 | Added a pull-up Resistor on a UART RXD PIN. Added a 100uF capacitor on DC JACK. |
| EL-1606 | rev0.1 20151201 | RILIM of NCP380 is changed to 6.49kΩ and USB current limits at 2A. |
| EL-1711 | rev0.1 20170905 | The Protection IC is changed from 2xNCP372 to 1xTPS259251. The Load S/W is changed from NCP380 to MP62551. The connect resistor of the HDMI shield pin has become 1M ohm. the next lot will be changed to 0 ohm. |
| EL-1908 | rev0.1 20180912 | Due to a PCB vendor's mistake, the PCB surface color was change to green from blue accidentally. |
| EL-2102 | rev0.2 20191126 | The HDMI level shifter IC is changed from IP4791CZ12 to TPD5S116. This change may result in a reduction in the Short Circuit Current from 350 mA to 120 mA and The 5V power current of sink draws less to 120mA from 140mA within 4.7V and 5.3V from source , Which may be insufficient for some VGA adapters that consume more current than the HDMI standard specification (50mA) or over 120mA. |
| EL-2108 | rev0.2 20191126 | Changed Q1, Q2, Q4 and Q5 from FTK7002EN to FTK7002U because of the semiconductor shortage. |
We did not change the PCB revision because any key features were not changed nor added.
Schematics and drawings
- Download Fritzing part for XU4 odroid-xu4.fzpz
Board Layout
Specifications
| Processor | Samsung Exynos5 Octa ARM Cortex™-A15 Quad 2Ghz and Cortex™-A7 Quad 1.3GHz CPUs |
| Memory | 2Gbyte LPDDR3 RAM at 933MHz (14.9GB/s memory bandwidth) PoP stacked |
| 3D Accelerator | Mali-T628 MP6(OpenGL ES 3.0/2.0/1.1 and OpenCL 1.1 Full profile) |
| Video | supports 1080p via HDMI cable(H.264+AAC based MP4 container format) |
| Video Out | Standard Type A HDMI connector |
| Audio | Instead of On-board Audio codec, There is I2S Expansion Port(CON11) |
| USB3.0 Host | SuperSpeed USB standard A type connector x 2 port, Max Load: total 2Amp for two USB 3.0 host ports |
| USB2.0 Host | High Speed standard A type connector x 1 ports, Max Load: 500mA/port |
| Display | HDMI monitor |
| Storage (Option) | MicroSD Card Slot, eMMC module socket : eMMC 5.0 HS4000 Flash Storage |
| Gigabit Ethernet LAN | 10/100/1000Mbps Ethernet with RJ-45 Jack ( Auto-MDIX support) |
| Serial console port | Connecting to a PC gives access to the Linux console. You can see the log of the boot, or to log in to the C1 to change the video or network settings. Note that this serial UART uses a 1.8 volt interface. We recommend the USB-UART module kit from Hardkernel. Molex 5268-04a(2.5mm pitch) is mounted on the PCB. Its mate is Molex 50-37-5043 Wire-to-Board Crimp Housing. |
| RTC (Real Time Clock) backup battery connector | If you want to add a RTC functions for logging or keeping time when offline, just connect a Lithium coin backup battery (CR2032 or equivalent). All of the RTC circuits are included on the ODROID-XU4 by default. Molex 53398-0271 1.25mm pitch Header, Surface Mount, Vertical type (Mate with Molex 51021-0200) |
| WiFi (Option) | USB WIFI Modules |
| HDD/SSD SATA interface (Optional) | SuperSpeed USB (USB 3.0) to Serial ATA3 adapter for 2.5“/3.5” HDD and SSD storage |
| Power (Option) | 5V 4A Power |
| Case(Option) | Mechanical case & cooler (90 x 59 x 28 mm approx. ) |
| PCB Size | 83 x 58 x 20 mm approx. |
Connectors
Expansion Connectors (CON10/CON11)
Expansion Connector Description
GPIO DC Electrical Characteristics (VDD = 1.80V)
| Parameter | Min | Max | Unit |
|---|---|---|---|
| Vih (High-level input voltage) | 0.7 x VDD | VDD+0.2 | V |
| Vil (Low-level input voltage) | -0.2 | 0.3 x VDD | V |
| dV (Hysteresis voltage) | 0.15 | V |
UART Console Connector
_____UART____ |Pin 4 - GND| |Pin 3 - RXD| |Pin 2 - TXD| |Pin 1 - VCC| \___________| 1.8V LVTTL interface Pin 1 : 1.8Volt output from XU4 board for the reference voltage for USB-UART board.
LED Indicators
The ODROID-XU4/HC1/HC2 has four indicator LEDs that provide visual feedback.
1. Red LED
- Power: connected to 5V power (HC2:12V)
2. Blue LED
- Alive Solid light : u-boot is running
- Flashing : Kernel is running (heart beat)
3. Ethernet LEDs
- Green LED Flashes when there is 100Mbps connectivity
- Yellow(Orange/Amber) LED Flashes when there is 1000Mbps connectivity
Regulatory Compliance Documents
<html>
<ul>
<li style=“text-align: left;”>The terms HDMI, HDMI High-Definition Multimedia Interface, HDMI Trade dress and the HDMI Logos are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.</li>
<li style=“text-align: left;”>HDMI, HDMI High-Definition Multimedia Interface(고화질 멀티미디어 인터페이스), HDMI 트레이드 드레스 및 HDMI 로고라는용어는 HDMI Licensing Administrator, Inc.의 상표 또는 등록 상표입니다.</li>
</ul>
</html>
neal