Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
odroid_go:go_assembling [2018/07/10 16:50]
justin [Main board]
odroid_go:go_assembling [2019/04/02 08:32] (current)
odroid [Warning & Caution]
Line 35: Line 35:
  
 <WRAP important>​ <WRAP important>​
-<color #​ed1c24>​Please be careful when you insert your LCD into the front enclosure, otherwise the LCD module may break.</​color>​\\+<color #​ed1c24>​Please be careful when you insert your LCD into the front enclosure, otherwise the LCD module may break.</​color>​\\  
 +<color #​ed1c24>​Refer to this video before assembling: [[https://​youtu.be/​6wwHmgX5U3w| Youtube - ODROID-GO LCD Assembly]]</​color>​\\ ​
 </​WRAP>​ </​WRAP>​
  
Line 55: Line 56:
  
 ==== Main board ==== ==== Main board ====
-Next is the main part of the assembling instructions. Please carefully put the ODROID-GO board in the front enclosure and connect the LCD cable to the board. After the LCD screen cable is firmly connected, you can fasten the main board with the screws (4x) enclosed.+Next is the main part of the assembling instructions. Please carefully put the ODROID-GO board in the front enclosure and connect the LCD cable to the board.\\ 
 +<color #​ed1c24>​You have to fully insert the LCD FPC cable into the connector. Otherwise, the display will not work from time to time.</​color>​\\ 
 +<color #​ed1c24>​The white line of FPC cable has to reach very close to the connector locker.</​color>​\\ 
 +After the LCD screen cable is firmly connected, you can fasten the main board with the screws (4x) enclosed.
  
 <WRAP important>​ <WRAP important>​
Line 73: Line 77:
 {{:​accessory:​odroid_go:​asm_20.jpg?​300|}} {{:​accessory:​odroid_go:​asm_20.jpg?​300|}}
  
-<color #​ed1c24>​You have to fully insert the LCD FPC cable into the connector. Otherwise, the display will not work from time to time.</​color>​+
 ==== Power key ==== ==== Power key ====
 Another piece which you have to cut on the plastic button set is the power key, and you can place the power switch at the side of the ODROID-GO. Another piece which you have to cut on the plastic button set is the power key, and you can place the power switch at the side of the ODROID-GO.
Line 96: Line 100:
  
 {{:​accessory:​odroid_go:​asm_25.jpg?​300|}} {{:​accessory:​odroid_go:​asm_25.jpg?​300|}}
-===== Warning & Caution =====+====== Warning & Caution ​======
 <WRAP important>​ <WRAP important>​
 <color #​ed1c24>​If you press the edges of the LCD panel too hard with your fingers while inserting the LCD, it may damage the TFT glass as shown below pictures. ​ </​color>​ <color #​ed1c24>​If you press the edges of the LCD panel too hard with your fingers while inserting the LCD, it may damage the TFT glass as shown below pictures. ​ </​color>​
Line 102: Line 106:
 {{:​odroid_go:​break_lcd1.jpg?​300|}} {{:​odroid_go:​break_lcd1.jpg?​300|}}
 {{:​odroid_go:​break_lcd2.jpg?​300|}} {{:​odroid_go:​break_lcd2.jpg?​300|}}
 +
 +====== Yet Another ODROID-GO Build Tutorial ======
 +This is a photo driven build tutorial for the ODROID-GO kit with a bunch of little tips along the way. Written by forum user @vbrusca.\\
 +[[http://​middlemind.net/​tutorials/​odroid_go/​odroid_go_build.html|Yet Another ODROID-GO Build Tutorial]]
 +