Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Last revision Both sides next revision
odroid_go_advance:application_note:sdio_wifi [2020/05/21 11:56]
joy.cho [Configuring WIFI station mode (2) - using command line]
odroid_go_advance:application_note:sdio_wifi [2020/09/03 17:02]
joy.cho
Line 1: Line 1:
 ====== How to configure built-in WIFI module ====== ====== How to configure built-in WIFI module ======
-<WRAP info round> 
-**This wiki page will be updated soon!!!** (2020.05.21) 
-</​WRAP>​ 
  
 <WRAP info round> <WRAP info round>
Line 8: Line 5:
 </​WRAP>​ </​WRAP>​
  
-  - WIFI KEY Features+  - Module Key Features
   - Configuring WIFI station mode (1) - using [Configuration] Menu   - Configuring WIFI station mode (1) - using [Configuration] Menu
   - Configuring WIFI station mode (2) - using command line   - Configuring WIFI station mode (2) - using command line
   - Configuring WIFI AP mode   - Configuring WIFI AP mode
-  - Checking basic connection +  - Checking basic connection ​of wlan0 
-  - Configuring ​Suspend/​Resume +  - Workaround to support ​Suspend/​Resume ​with esp8089 module 
-===== WIFI Key Features ===== +===== Module ​Key Features ===== 
-  ​* ​ESP-WROOM-S2 ​that integrates ​ESP8266EX + 
-  ​* ​WIFI Protocol ​802.11 b/g/n +^ Items            ^ Specifications ​                             ^ 
-  Frequency Range 2.4 GHz ~ 2.5 GHz (2400 MHz ~ 2483.5 MHz) +| Module ​          ​| ​ESP-WROOM-S2 ​                               | 
-  ​* ​SDIO interface up to 50 MHz, SDIO v2.0+| MCU              | ESP8266EX ​                                  | 
 +WIFI Protocol ​   ​| ​802.11 b/g/n, up to 72.2 Mbps of data rate  
 +Frequency Range  ​| ​2.4 GHz ~ 2.5 GHz (2400 MHz ~ 2483.5 MHz)   | 
 +| Interface ​       | SDIO interface up to 50MHz, SDIO v2.0       |
  
  
Line 27: Line 27:
  
 ===== Configuring WIFI station mode (2) - using command line ===== ===== Configuring WIFI station mode (2) - using command line =====
-Check **esp8089** module is loaded normally.+Or you can establish WIFI network using the following instuctions.\\ 
 +\\ 
 +First, check **esp8089** module is loaded normally.
 <code bash target> <code bash target>
 $ lsmod $ lsmod
Line 75: Line 77:
  
 ===== Configuring WIFI AP mode ===== ===== Configuring WIFI AP mode =====
 +There is no GUI menu to configure WIFI AP mode for now.\\ 
 +Please use the following instruction via command line.
 === 1. Update & Upgrade === === 1. Update & Upgrade ===
 <code bash target> <code bash target>
Line 91: Line 94:
 $ sudo systemctl disable dnsmasq $ sudo systemctl disable dnsmasq
 </​code>​ </​code>​
-=== 3. Setup (1) - Configuration ​a static IP ===+=== 3. Setup (1) - Configuring ​a static IP ===
 To configure the static IP address, please edit a dhcpcd configuration file, /​etc/​dhcpcd.conf.\\ To configure the static IP address, please edit a dhcpcd configuration file, /​etc/​dhcpcd.conf.\\
 Go to the end fo this file and add the following lines.\\ Go to the end fo this file and add the following lines.\\
Line 136: Line 139:
 </​code>​ </​code>​
 <code bash target> <code bash target>
-# DAEMON_CONF=""​ 
 DAEMON_CONF="/​etc/​hostapd/​hostapd.conf"​ DAEMON_CONF="/​etc/​hostapd/​hostapd.conf"​
 </​code>​ </​code>​
Line 143: Line 145:
 Add the following information in the dnsmasq configuration file, /​etc/​dnsmasq.conf.\\ Add the following information in the dnsmasq configuration file, /​etc/​dnsmasq.conf.\\
 <code bash target> <code bash target>
-#stop DNSmasq from using resolv.conf+$ vi /​etc/​dnsmasq.conf 
 +</​code>​ 
 +<code bash target>​ 
 +If you don't want dnsmasq to read /etc/resolv.conf ​or any other 
 +# file, getting its servers from this file instead (see below), then 
 +# uncomment this.
 no-resolv no-resolv
-#Interface ​to use+ 
 +If you want dnsmasq ​to listen for DHCP and DNS requests only on 
 +# specified interfaces (and the loopback) give the name of the 
 +# interface (eg eth0) here. 
 +# Repeat the line for more than one interface.
 interface=wlan0 interface=wlan0
 +
 +# On systems which support it, dnsmasq binds the wildcard address,
 +# even when it is listening on only some interfaces. It then discards
 +# requests that it shouldn'​t reply to. This has the advantage of
 +# working even when interfaces come and go and change address. If you
 +# want dnsmasq to really bind only the interfaces it is listening on,
 +# uncomment this option. About the only time you may need this is when
 +# running another nameserver on the same machine.
 bind-interfaces bind-interfaces
 +
 +# Uncomment this to enable the integrated DHCP server, you need
 +# to supply the range of addresses available for lease and optionally
 +# a lease time. If you have more than one network, you will need to
 +# repeat this for each network on which you want to supply DHCP
 +# service.
 dhcp-range=192.168.4.3,​192.168.4.20,​12h dhcp-range=192.168.4.3,​192.168.4.20,​12h
 </​code>​ </​code>​
Line 162: Line 187:
 === 7. Start services === === 7. Start services ===
 <code bash target> <code bash target>
-service ​dnsmasq ​start +sudo systemctl enable ​dnsmasq 
-service hostapd ​start +sudo systemctl ​start dnsmasq
-</​code>​+
  
 +$ sudo systemctl enable hostapd
 +$ sudo systemctl start hostapd
 +</​code>​
 +<code bash target>
 +$ ip addr
 +1: lo: <​LOOPBACK,​UP,​LOWER_UP>​ mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1
 +    link/​loopback 00:​00:​00:​00:​00:​00 brd 00:​00:​00:​00:​00:​00
 +    inet 127.0.0.1/8 scope host lo
 +       ​valid_lft forever preferred_lft forever
 +    inet6 ::1/128 scope host 
 +       ​valid_lft forever preferred_lft forever
 +2: wlan0: <​BROADCAST,​MULTICAST,​UP,​LOWER_UP>​ mtu 1500 qdisc mq state UP group default qlen 1000
 +    link/ether ab:​cd:​ef:​12:​34:​56 brd ff:​ff:​ff:​ff:​ff:​ff
 +    inet 192.168.4.1/​24 brd 192.168.4.255 scope global noprefixroute wlan0
 +       ​valid_lft forever preferred_lft forever
 +    inet6 fe80::​1234:​1234:​1234:​1234/​64 scope link 
 +       ​valid_lft forever preferred_lft forever
 +</​code>​
 ===== Checking basic connection ===== ===== Checking basic connection =====
 +If you get fails during network setup, please check the followings using ssh with a USB-to-Ethernet adapter or UART console.
 +
 === mmc1 node === === mmc1 node ===
 <code bash target> <code bash target>
Line 196: Line 240:
 </​code>​ </​code>​
  
-===== Configuring ​Suspend/​Resume =====+===== Workaround to support ​Suspend/​Resume ​with esp8089 module ​=====
  
 **/​lib/​systemd/​system-sleep/​sleep**\\ **/​lib/​systemd/​system-sleep/​sleep**\\