Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
old_product:etc:odroidoduinoone [2013/11/04 15:38]
odroid [Qt(Ubuntu arm)]
old_product:etc:odroidoduinoone [2019/03/06 08:41] (current)
odroid [Android]
Line 15: Line 15:
 Connections are (V)oltage, (S)ignal, (G)round Connections are (V)oltage, (S)ignal, (G)round
  
-{{en:​dht11-humiditytempvsg.jpg}}+{{en:oduinoone:​dht11-humiditytempvsg.jpg}}
  
 DHT11 uses one-wire communication and I connected it to the digital Pin#3 of Arduino. DHT11 uses one-wire communication and I connected it to the digital Pin#3 of Arduino.
 Also note that we should add a 10Kohm pull-up resistor on that pin. Also note that we should add a 10Kohm pull-up resistor on that pin.
  
-{{en:s_20131020_184658.jpg}}+{{en:oduinoone:​oduinoone_side.jpg?600|}}
  
 The example code shows the temperature,​ humidity and pressed keypad information on LCD. The example code shows the temperature,​ humidity and pressed keypad information on LCD.
 It also transmit that information to the host via USB. It also transmit that information to the host via USB.
  
-{{en:s_20131020_173251.jpg}}+{{en:oduinoone:​oduinoone_top.jpg?600|}}
  
  
 To compile this source code, you need to install the Arduino IDE on your ODROID board or PC. To compile this source code, you need to install the Arduino IDE on your ODROID board or PC.
-[code] +<code> 
-sudo apt-get install arduino +sudo apt-get install arduino 
-[/code]+</code>
  
 I could run the Arduino IDE on ODROID with Ubnutu image. I could run the Arduino IDE on ODROID with Ubnutu image.
Line 44: Line 44:
 I should restart the Arduino IDE after copying to use the library. I should restart the Arduino IDE after copying to use the library.
  
-[code]+<code>
     #include <​LiquidCrystal.h>​     #include <​LiquidCrystal.h>​
     #include <​dht.h>​     #include <​dht.h>​
Line 182: Line 182:
          ​delay(50);​ // delay 50 msec.          ​delay(50);​ // delay 50 msec.
     }     }
-[/code]+</code>
  
 ===== Application ===== ===== Application =====
Line 191: Line 191:
 http://​dn.odroid.com/​ODUINO/​binary/​Ubuntu_Qt/​arm/​oduino http://​dn.odroid.com/​ODUINO/​binary/​Ubuntu_Qt/​arm/​oduino
  
-{{http://​dn.odroid.com/​ODUINO/​binary/​Ubuntu_Qt/​screenshot,​ 2013-11-04 14:​32:​15.png}}+{{http://​dn.odroid.com/​ODUINO/​binary/​Ubuntu_Qt/​screenshot,​ 2013-11-04 14:​32:​15.png?600|}}
  
 The binary & source code of PC Application. The binary & source code of PC Application.
Line 198: Line 198:
 == install packages == == install packages ==
 <​code>​ <​code>​
-apt-get install qt4-default qt4-designer libqwt-dev+$ sudo apt-get install qt4-default qt4-designer libqwt-dev
 </​code>​ </​code>​
 == build the oduino == == build the oduino ==
Line 208: Line 208:
 </​code>​ </​code>​
  
 +== Tip ==
 +If you need the application with Qt5, refer this link.\\
 +http://​forum.odroid.com/​viewtopic.php?​f=90&​t=8524#​p104675
 ==== Android ==== ==== Android ====
 http://​dn.odroid.com/​ODUINO/​binary/​Android/​Oduino.apk http://​dn.odroid.com/​ODUINO/​binary/​Android/​Oduino.apk
  
-{{http://​dn.odroid.com/​ODUINO/​binary/​Android/​Screenshot_2013-11-04-14-46-26.png}}+{{http://​dn.odroid.com/​ODUINO/​binary/​Android/​Screenshot_2013-11-04-14-46-26.png?600|}}
  
-The binary & source code of Android Application.+The binary & source code of the Android Application.\\
 http://​dn.odroid.com/​ODUINO/​source/​Android/​Oduino.zip http://​dn.odroid.com/​ODUINO/​source/​Android/​Oduino.zip